FURY BEAR Euro6 Sound System Module For 1/14 Trucks

产品设计、外观、性能及使用要求。

1 Statement
Thank you for your trust in FuryBear products. Incorrect use
may result in personal injury and equipment damage. Please read the instruction manual carefully before using the equipment and strictly observe the specified operation.
read the manual carefully before using the equipment and strictly follow the specified operating
procedures. We do not assume any responsibility for any damage caused by the use of this product.
We do not assume any liability arising from the use of this product.
We reserve the right to make changes without notice. We reserve the right to change the design, appearance, performance and requirements for use of the product without notice.
design, appearance, performance and requirements for use of the product without notice.

2 Precautions
- Before using the sound set, carefully read all the manuals of the associated electronic equipment to make sure that the power supply is properly configured.
- The sound unit must be used in Climb mode. The Quiron wp1080 ESC is recommended.
-The sound set is not waterproof. Avoid water ingress, as this may cause the internal circuits to short out.
-When connecting the sound set to related equipment, make sure that all connecting cables and connecting parts are well insulated: all connecting cables are connected correctly: the input and output voltages of each part are correct.
The input and output voltages of the components are correct. Incorrect connections and misrecognized voltages can damage the SSM.
-There is no separate switch for the sound group. When energized, the ESC switch is used to control the startup and shutdown of the sound set. Remember to disconnect the battery when the ESC is turned off.
If the battery is not disconnected, the unit's high voltage input terminals will continue to draw very little current even if the ESC switch is turned off. If you leave the battery connected for a long time, the battery will eventually be completely discharged.
If the battery is left connected for an extended period of time, the battery will eventually become fully discharged, causing the battery or the sound pack to malfunction.

3产品介绍
• 外形尺寸小巧，集成度高
• 全金属外壳设计，保护芯片，提高内部散热能力。
• 高低压分离的设计消除了电流声，提高了音质。
• 以声组核心，通过其内部程序集成所有操作命令，然后再将命令输出到电调、
灯光控州和：
形成完整的控制系统。总线输出不仅减少了复杂的线路连接，而且扩展性更强。
•凭借FuryBear独特的仿真模拟算法，更真实的还原不同转速时的发动机音效，
• 非常精细的声音采样，带来更丰富的效果表现。
•为不同车型设计的特定程序使音效更加匹配。

3Product Description
- Compact size and high integration
- Full metal shell design, protect the chip, improve internal heat dissipation ability
- High and low voltage separation design eliminates current sound and improves sound quality.
- With the core of the sound group, it integrates all the operation commands through its internal program, and then outputs the commands to the ESC,
Lighting control state and:
forming a complete control system. The bus output not only reduces complex wiring connections, but is also more expandable.
-With FuryBear's unique simulation algorithm, it can more realistically restore the engine sound effect at different RPM.
- Very fine sound sampling, bringing richer effect performance.
-Specific programs designed for different car models make the sound effect more compatible.

4 线路连接
警告上电前请确认接线和电压，否则会烧坏电路
灯光总线
插入接收机
转向舵机

5 操作
• 首先连接电池并打开电调电源。声组将发出排气声音提示，并进入工作状态
• 声组通过邏控器上的三档开关控制发动机启动、停止和空气喇叭。如果没有启动发动机的音效，电机将不
会输出动力。如果要在静音状态下操作车辆，可以通过邏控器的旋钮通道控制声组的输出音量
• 发动机声音效果启动后，车辆开始时处于空档状态，只有在挂档后才能控制车辆前进成倒车，
• 油门和刹车为定速模式，当油门杆回中时，车辆将保持当前速度。如果您想在松开油门时让车辆有滅速效
果，只需降低油门微调即可，做调量会改变减速速度。
• 当车辆向前和向后切换时，需要将车辆刹车到静止状态，以便成功切换，并且伴有换档声音效果
• 声组的总线接口为灯光控制，需要与furabear生产的灯光模块连接，以实现整车灯光。

5 Operation
- First connect the battery and turn on the ESC power. The sound unit will emit an exhaust audible tone and go into operation.
- The sound group controls engine start, stop and air horn via the three-position switch on the logic control. If there is no sound effect to start the engine, the motor will not
The motor will not output power. If the vehicle is to be operated in silent mode, the output volume of the sound unit can be controlled through the knob channel of the logic control.
- When the engine sound effect is activated, the vehicle starts in neutral and can only be controlled in forward or reverse when in gear, the throttle and brake are in constant speed mode.
- The throttle and brake are in constant speed mode, and the vehicle will maintain its current speed when the throttle lever is back in center. If you want the vehicle to have the effect of slowing down when you release the gas pedal, just lower the throttle slightly and adjust the brake.
If you want the vehicle to have a deceleration effect when you let off the throttle, just reduce the throttle trim, the amount of trim will change the deceleration speed.
- When switching from forward to backward, you need to brake the vehicle to a standstill in order to successfully switch and have the gearshift sound effect.
- The bus interface of the sound group is for light control, which needs to be connected with the light module made by furabear to realize the whole vehicle light.